Cortech CREASEMASTER PLATINUM CREASING SYSTEM Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Cortech CREASEMASTER PLATINUM CREASING SYSTEM. Cortech CREASEMASTER PLATINUM CREASING SYSTEM User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 44
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Page 1
CreaseMaster Platinum - Reference Manual
Table of Contents
1.0 General Operation
1.1 Technical Data
1.2 Safety Regulations
1.3 Cautions Concerning Machine
2.0 Machine Assembly
2.1 Power Supply Instructions
2.2 Air Regulator Instructions
3.0 Getting Ready
3.1 Paper Gate Adjustments
3.2 Side Rail Set Up
3.3 Air Nozzle Set Up
3.4 Vacuum/Blower Adjustments
3.5 Optional Conveyor Out Feed
4.0 Setting Up a Job
4.1 Operating the Touch Screen
5.0 Idler Wheels/Perforating/Slitting
5.1 Idler Wheels
5.2 Perforating/Slitting
6.0 Cleaning & Maintenance
6.1 Cleaning
6.2 Maintenance
Diagrams and Parts Listing
Vue de la page 0
1 2 3 4 5 6 ... 43 44

Résumé du contenu

Page 1 - Table of Contents

Page 1 CreaseMaster Platinum - Reference Manual Table of Contents 1.0 General Operation 1.1 Technical Data 1.2 Safety Regulations 1.3 Caut

Page 2 - 1.2 SAFETY REGULATIONS

4.1 OPERATING THE TOUCH SCREEN This is the initial start up screen that appears once the machine is turned on. Approximately 2 minu

Page 3

This screen appears after pressing the “ Program New Job ” key. This screen allows you the option of Batching. You are able to input

Page 4

This screen appears after pressing the “ Next “ key. The number number “1” signifies the first crease you are going to program. Press the

Page 5 - 2.0 Machine Assembly

Pressing the Previous (PREV) key will return you back to the previous screen displayed. You will not lose information programmed into the crea

Page 6

After the 10th crease is programmed, pressing the NEXT key will advance you to the Strike Perf screen. Pressing the CREASE COMPLETE key wil

Page 7

This screen is the first one to be displayed should you want to use the pneumatic Strike Perf option OR if you want to continuously perf a p

Page 8 - 3.0 Getting Ready

CONTINUOUS PERF USING STANDARD ACCESSORY HOLDER This screen does not affect continuous perf. Press the SKIP TEST PAGE key to adva

Page 9

CONTINUOUS PERF USING STANDARD ACCESSORY HOLDER Press the RUN key to begin the job. Page 17

Page 10 - Page 10

CONTINUOUS PERF USING STANDARD ACCESSORY HOLDER Press the RUN key to start the job running. Pressing the MAIN Key will return yo

Page 11

If you want to use the Strike Perf accessory holder to do continuous perfing, press the ContinuousPerf key.. If you want to program the S

Page 12 - Page 12

Page 2 1.1 TECHNICAL DATA Areas of Use: Paper Weight: 12# - 18 point (45-385 gsm) Paper Formats: Maximum 18”x 25.5” (45x57 cm)

Page 13 - Page 13

Press the 0.00 key to activate the keypad menu. Enter the length of the page and press the Enter key to proceed. Press the NEXT key t

Page 14 - Function****

Perf is to turn off. You can repeat this sequence up to 5 times. If no more Strike Perf locations are needed, press the Next button key and proceed

Page 15 - Page 15

Pressing PREV takes you back one screen to where you can select to run a test page or not. The Run and Save key allows you to program a

Page 16 - Page 16

Press the key to activate the keypad. The and keys scroll through the whole alphabet in upper and lo

Page 17 - Page 17

Once you have read this message, press NEXT to continue. The UP and DOWN keys referred to in the message are 2 screens forward from here.

Page 18 - Page 18

Pressing the Run Now key advances you to the run menu. (See page 26) Pressing the Return to Main Menu key returns you to the initial W

Page 19

The Run menu screen allows you to control certain aspects of how the job will run. The speed can be adjusted using the UP and DOWN keys to

Page 20

Press the UP or DOWN keys so that the job to be run is displayed. Press the OPEN SAVED JOB key to proceed. If the contents of the

Page 21 - Page 21

Other Screens: Safety Lid Must Be Closed For Machine to Run Page 28 You Must Decrease Speed Of The Machine if Crease Is To Close

Page 22 - Page 22

Idler Wheels/Perforating/Slitting 5.1 Idler Wheels The Idler Wheels (rubber tires on the accessory holders) are used to stabilize the stock as i

Page 24

Perforating, and/or slitting can be performed with or without a score. As previously mentioned, if no scoring is desired, program ‘00’has been set a

Page 25 - Page 25

Page 31 through the machine square, you can feed a sheet into the machine using the hand wheel and align the lead edge of the sheet with a straight

Page 26 - Page 26

Page 32 6.0 Maintenance 6.1 Cleaning After each job, or halfway (approximately 24 hrs) through a very long job, it is recommended that the ma

Page 29 - Accessory Holder

Page 35 PARTS PART NO. Jr. 3K 6K 8K 8KP 12K FM FM CM CM CM AIR DESCRIPTION (J-1) 100 150 PRO FRIC PLUS FEED

Page 30 - Boss Wheel

Page 36 10-029-GW X X X X X X X X Feed Shaft Bushing w/Spring 10-030-GW X X X X X X X X X X Shaft Bushing w/S

Page 31 - Page 31

Page 37 10-092-GW X X X X X X X X X X 4 TPI Perf. Blade 10-093-GW X X X X X X X X X X 6 TPI Perf. Blade 10-09

Page 32 - 6.0 Maintenance

Page 38 20-002-GW X Register Lay Sheet 20-003-GW X Crash Pad 20-005-GW X

Page 33 - Page 33

Page 39 60-016-GW X X Conveyor Belt 60-017-GW X X Conveyor Belt Spool 60-020-GW X

Page 34 - Page 34

CM Platinum Machine Diagram Exit Tray GuideMagnetic StopLaser/PhotoEyePaper Gate AssemblyRegistration Holes for aligning Op sideSide Rail 1.0

Page 35 - Page 35

Page 40 90-030-GW X X X X X Telephone Cable 90-031-GW X X X X X X X X X X Low Profile Tie Mounts 90-032-GW

Page 36 - Page 36

Page 41 94-034-GW X X X X X Display Board Label (ALL MODELS SN 2111 AND HIGHER ) 94-034-8-GW X X Oper

Page 37 - Page 37

Page 42 CM-0003N X X X Bottom Die Narrow CM-0003LC X X X Bottom Die Combination Narrow / Wide CM-0003S

Page 38 - Page 38

Page 43 FLD-0099 X X Side Rail Ops Side FLD-0100 X X Side Rail Non Ops Side FLD-0108 X X X X X

Page 39 - Page 39

Page 44 RN028 X X X X X X unit numbering wheel retaining pawl RN029 X X X X X X 2x/4x action ratchet wheel ret

Page 40 - Page 40

2.0 Machine Assembly Remove and unpack all machine parts from the shipping carton. 2.1 Power Supply Instructions Before connecting the power cord

Page 41 - Page 41

2.2 Air Regulator Assembly The CreaseMaster Platinum score dies are pneumatically driven. The air pressure is regulated from the air source (whether

Page 43 - Page 43

3.0 Getting Ready 3.1 Paper Gate Adjustments • With light to medium stock, the feed finger should be not adjusted down, as the front nozzles will

Page 44 - Page 44

3.3 Nozzle Positioning • The nozzles should be positioned according to the following diagram • Note: Very wide stock will require the nozzles to b

Commentaires sur ces manuels

Pas de commentaire